Title | : | BEST Subwoofer for under $100? Will Shake your House! ISO-100 Mega earthquake |
Lasting | : | 11.20 |
Date of publication | : | |
Views | : | 200 rb |
|
i recently made a new enclosure for my old z2300 sub (only used the sub for a few years) and well, F3 of the original was 56Hz, new F3 is 27, it's incredible what you can do with existing speakers and 30€ for mdf gets you Comment from : Rydex |
|
At low frequencies your subs are moving quite a bit When subs move they change impedance It's called rise You could've ran them at 2 ohms and your amp would never see it Comment from : cdbennett |
|
Its called isobarric kicker did it in 75 Comment from : Larry Montgomery |
|
Isobaric W7's Comment from : Foldy Holds |
|
Of course your large sealed system will be the best, I'm sealed fan myselfthe BR is OK and the performance is nice, but do you hear some mechanical noise from the reversed drivers When I made push pulls like this the noise was always a drawback Comment from : Dimitar Atanasov |
|
Antônio from Brazil Nice job changing 0,9 QTS cheap drive to a 0,45 Qts nice subwoofer Comment from : 80 deciBeis |
|
have you tried using this sub for music? or is this mostly for a home theater application Comment from : Frank Martines |
|
I enjoyed this video Toid I just bought a set of inexpensive subwoofers the GRS 10SW-4HE They are currently about $55 each Of course the QES is much lower as it has a much stronger motor and 11mm Xmax vs 85 compared to the ones you used in your video They model very well in WinISD I suspect they may not of been available at the time you built your project I was going to build them with a ported enclosure but now decided to just go with a sealed design I figure with room gain I should be just fine; but now wish I had bought the 12SW-4HE's they work in the same size box but handle about double the power before XMax is an issue I have done that a lot Buy drivers only to change my mind for a different pair before I even start to build the enclosure Comment from : jimthvac100 |
|
Nice budget! May I suggest painting "eyes" on the rear of the woofers Comment from : MrRonnmaui |
|
I built two enclosures with 4 Skar Audio IX-10 D2 10" 400 each powered by Crown XLS 2002 that's eight subs at 4 ohms This is one outstanding sub I have tuned in at 24hz and frankly, I have unlimited power since I own a brand new Yamaha RX-A6A with independent sub-outputs I have every 4 subs on one side spending $2000 -$ 4000 on a retail sub is insane brthere is a company called stereo integrity they make the best subs I ever heard, Comment from : @JDlBrooks7 |
|
I'm just curious, my friend Have you ever built a powered midrange dual 10-inch Eminence array box? Comment from : Pablo Martínez |
|
cant you do it back to back? Comment from : yunus YILMAZ |
|
Can someone give me the enclosure specs for just TWO of the GRS drivers? Im assuming just one port? Comment from : Dave Kopke |
|
Why can't you just reverse the subs so that the magnets are inside the box yet still have them out of phase? Wouldn't that do the same thing as to what you are doing now? Comment from : James Cox |
|
I'm actually sitting about 5 feet from a ported 18" cabinet that's almost exactly 6 cubic feet after accounting for driver and structural volumes :D tuned to approximately 27 Hz but it's for my bass guitar so that's plenty low, I had to downtune my 5-string 2 full steps to hit that low G at 2450 Hz, and considering going lower since it's still quite loud and tonal Might even go all the way to E0 (2060Hz) on my B0 string since there's still enough SPL to hurt your unprotected ears Comment from : Paul Deck |
|
Whats the cheapest subwoofer to get clean 10hz That would be a nice video Thanks Comment from : oopsorry |
|
These subs are on sale right now for $30 eachMIght stock up!! Comment from : Arrow Imaging |
|
Please subtitles for the deaf Comment from : ji Steve |
|
I hear Russia tanks are coming hide yourself Comment from : Wilfredo Cortez |
|
I built a box with just 1 of the GRS 12 4he version - down firing The internal volume came out to 385 Cu Ft Using 4" abs for the port It sounds great and goes down to around 18hz I added a 5/8 inch thick mdf top and did an epoxy pour on it Turned out beautifully Looks like a nice coffee table in the corner near the couch (main listening position Comment from : Denis Vandale |
SVS SB1000 Pro Subwoofer Review - Best Subwoofer Under $500 РѕС‚ : cheapaudioman Download Full Episodes | The Most Watched videos of all time |
BEST Subwoofer Under $1000 XTZ 1x12 Edge Home Theater Subwoofer Review РѕС‚ : Shane Lee Download Full Episodes | The Most Watched videos of all time |
2023 Car Audio Subwoofer guide. Every wonder what is the best subwoofer set up for your car? РѕС‚ : Breakers Stereo u0026 Performance Download Full Episodes | The Most Watched videos of all time |
Sesame Street: Song: Shake Shake The Mango Tree РѕС‚ : Sesame Street Download Full Episodes | The Most Watched videos of all time |
Megabass 3 (1991) (Megamix Acid House, House, Euro House, Hip-House) РѕС‚ : Maicon Nights DJ Download Full Episodes | The Most Watched videos of all time |
Huge vs. Tiny Subwoofer | Why You Need A Subwoofer for Home Theater, Music РѕС‚ : Digital Trends Download Full Episodes | The Most Watched videos of all time |
Moroccan earthquake death toll continues to rise, Biden visits Vietnam, and more | CBS News Mornings РѕС‚ : CBS News Download Full Episodes | The Most Watched videos of all time |
Earthquake Drill ? РѕС‚ : Carmel Child Development and Learning Center, Inc. Download Full Episodes | The Most Watched videos of all time |
ISO 45001:2018 Occupational Health and Safety Management System РѕС‚ : smglearning Download Full Episodes | The Most Watched videos of all time |
All Countries Phone Codes | Country Codes | Dialing Codes | ISO Country Codes РѕС‚ : Worldostats Download Full Episodes | The Most Watched videos of all time |